8F9952FF-A413-4652-876A-9A8CC2B15A6E.jpg
84GSLSE 13BREW Swap build
-
DWNUNDR
- VIP User
- Posts: 256
- Joined: Sat Jan 20, 2018 4:02 pm
- Has thanked: 38 times
- Been thanked: 46 times
Re: 84GSLSE 13BREW Swap build
You do not have the required permissions to view the files attached to this post.
-
Casey
- Admin
- Posts: 1347
- Joined: Sat May 07, 2011 5:46 pm
- Location: Colchester, UK
- Has thanked: 443 times
- Been thanked: 324 times
Re: 84GSLSE 13BREW Swap build
Are these seats with electric seat adjustment and seat heaters? If so, it would be great to hook them up 
KIMI 1 : 1st Gen, "hybrid" 1983 silver S2 running gear in a 1985 S3 shell, SORN'd, long term resto project
KIMI 2 : 1st Gen, 1983 silver S2 - now sold to Ian Mothersole on here.
KIMI 3 : 1st Gen, 1983 red S3
Plus a 2004 Full Bridgeported RX-8
KIMI 2 : 1st Gen, 1983 silver S2 - now sold to Ian Mothersole on here.
KIMI 3 : 1st Gen, 1983 red S3
Plus a 2004 Full Bridgeported RX-8
-
DWNUNDR
- VIP User
- Posts: 256
- Joined: Sat Jan 20, 2018 4:02 pm
- Has thanked: 38 times
- Been thanked: 46 times
Re: 84GSLSE 13BREW Swap build
yes.. I plan on getting power to the adjuster motors but havent decided on heaters... not sure I want to be driving this in winter hahah
-
DWNUNDR
- VIP User
- Posts: 256
- Joined: Sat Jan 20, 2018 4:02 pm
- Has thanked: 38 times
- Been thanked: 46 times
Re: 84GSLSE 13BREW Swap build
little more wiring done... issues with pump trigger now so I will bypass it with a switch...
got the wideband mostly hooked up now and ope to figure out how to power the drivers seat soon now that the mount worked perfectly...
got the wideband mostly hooked up now and ope to figure out how to power the drivers seat soon now that the mount worked perfectly...
-
DWNUNDR
- VIP User
- Posts: 256
- Joined: Sat Jan 20, 2018 4:02 pm
- Has thanked: 38 times
- Been thanked: 46 times
Re: 84GSLSE 13BREW Swap build
decided to go ahead and take a chance on the changes I had made to the design of the drivers mount.. tape measure measurements and guesses on the changes and voila... almost sits flat.. it is about an inch higher on the passenger side once seat is on the mount.. tonight I should finish up welding the seat to the mount...
-
ian65
- Admin
- Posts: 6402
- Joined: Wed Mar 30, 2011 12:11 am
- Has thanked: 232 times
- Been thanked: 276 times
Re: 84GSLSE 13BREW Swap build
nice work on those mounts 
1999 Jaguar XJR V8 Supercharged
1992 Peugeot 205 1.9 GTI
2003 Mercedes SLK 200 Kompressor
-
DWNUNDR
- VIP User
- Posts: 256
- Joined: Sat Jan 20, 2018 4:02 pm
- Has thanked: 38 times
- Been thanked: 46 times
Re: 84GSLSE 13BREW Swap build
Figured out the power to my driver seat last night.. not using the heated seat part just the movements...
-
DWNUNDR
- VIP User
- Posts: 256
- Joined: Sat Jan 20, 2018 4:02 pm
- Has thanked: 38 times
- Been thanked: 46 times
Re: 84GSLSE 13BREW Swap build
gave up on waiting on mates who are busy... so started bodywork and paint prep
-
DWNUNDR
- VIP User
- Posts: 256
- Joined: Sat Jan 20, 2018 4:02 pm
- Has thanked: 38 times
- Been thanked: 46 times
Re: 84GSLSE 13BREW Swap build
after some work being done over the last week or so I got to my doors and discovered my ds door was bent... didnt want to spend $100+ on a tool for pulling dents so I used some bolts, some heat and a vice grip haha.. minimal bondo used despite what it appears... it has to be sanded down yet
