Page 16 of 18

Re: Project 'Dont fear the rotor'

Posted: Mon May 12, 2014 5:17 pm
by A7RXY
I have just found this
http://www.aaroncake.net/rx-7/damage.htm

A new one to me ........ Thanks Tool

Dibs

Re: Project 'Dont fear the rotor'

Posted: Tue May 13, 2014 12:15 am
by codge
X 2 TOOL.....Thanks.

Re: Project 'Dont fear the rotor'

Posted: Tue May 13, 2014 12:24 am
by Hobbawobba
I've read about this on here before http://www.mazdatrix.com/faq/pulley.htm. Its also linked into what Dibs posted.

Rear end looks good aye man! Gilmer is pretty sweet too and in an usual colour th: . Gotta get mine fitted once I get an e-fan haha.

Re: Project 'Dont fear the rotor'

Posted: Tue May 13, 2014 6:59 pm
by RamoNZ
Press clutch and hold it down with a stick works for me.

Re: Project 'Dont fear the rotor'

Posted: Tue May 20, 2014 9:09 pm
by Rexi84
I think its the angle the photo was taken but if it is too big im sure the wind will rip it off at speed or it will act as an air brake. :lol:
The gilmer drive is apparantly the last black one extreme rotaries had as they are only going to be selling silver from now on, there cutting there list of products down. You cant beat the noise of a gilmer drive either 8-)

Re: Project 'Dont fear the rotor'

Posted: Wed May 21, 2014 6:59 pm
by BO0557
looks very nice with the US spec rear ;)

gilmers do look good annodised black!! think i might need to do that for my spare set for my cosmo motor :)

Re: Project 'Dont fear the rotor'

Posted: Wed May 21, 2014 9:01 pm
by spirit r
Rexi84 wrote:You cant beat the noise of a gilmer drive either 8-)
Pure clear bridgport Sound will beat it, it's music you need it like junkies her drugs.
No Turbo noise, no gilmer noise only Sound of bridgy sloppy idle :D
Thomas

Re: Project 'Dont fear the rotor'

Posted: Wed May 21, 2014 9:34 pm
by ian65
spirit r wrote:
Rexi84 wrote:You cant beat the noise of a gilmer drive either 8-)
Pure clear bridgport Sound will beat it, it's music you need it like junkies her drugs.
No Turbo noise, no gilmer noise only Sound of bridgy sloppy idle :D
Thomas
nah, turbo every time.... bridgeport sounds like a council lawnmower :lol:

Re: Project 'Dont fear the rotor'

Posted: Thu May 22, 2014 4:51 pm
by spirit r
ian65 wrote:nah, turbo every time.... bridgeport sounds like a council lawnmower :lol:
That's it. So i knew my love cutting gras coming from
    :lol: And i dislike High skirl of the women :D
    THOMAS

    Re: Project 'Dont fear the rotor'

    Posted: Sat Jul 05, 2014 4:54 pm
    by Rexi84
    Bit of an update with a few bits and bobs that have been done over last couple of weeks.

    Fitted a new back box, always wanted one of these and now i have one. Its a tad loud. :D
    Image

    Image

    Image

    Its been made so that the original back box that was on it can be swapped back over quick and easy if i start going deaf.

    Image

    Image

    Image

    Image

    Image

    Bit of a video of it running, sound quality not the best as it was my phone but you get the idea.

    Image

    Only 2 pics i have from retro car mania at Weston park, as usual everybody more interested in rusty shite dropped on there arse and a bloody vespa that decided to park between me and the car next to me and even caught somebody leaning against my car to get a snap shot of said vespa. Arseholes. :x :x :x
    Wasn't till i started the car to go home early that it was like flies round shit and i couldnt move for the amount of people around the car.

    Image

    Image

    Finally have my forum decal on the car, thanks marc. 8-)

    Image

    Got some new carb bling too so fitted it all up

    Image

    And have purchased this said bit of special kit from the U.S that arrived last week

    Image